
3″ submersible pump of KMP INDUSTRRIES are designed to operate in a fully submerged environment where you can connect up the discharge hose, and throw them inside borewell where minimum inner diameter has to be 75 mm . In a simple word it is a very flexible machine for you. The pumps are made with high quality raw materials in order to extract best performance with lowest operating cost.
| Power Range | 0.75 H.P – 2 H.P |
|---|---|
| Head Range | 25 mtrs – 120 mtrs |
| Discharge | 20 LPM |
| Operating Voltage | ( 180 V – 230 V ) – ( I Phase ) |
| Outlet Size | 25 mm |
| Method of starting | Capacitor start and capacitor run |
| Maximum permissible amount of sand in water | 15 GRAM / Cubic meter |
| Outer pipe | S.S. 202 |
|---|---|
| Shaft | S.S. 410 |
| Impeller / Diffuser | Noryl |
| Thrust bearing set | Impregnated Carbon / S.S |
| Bearing Bush | LTB 4 |
4″ Stainless Steel Submersible pumpsets of KMP INDUSTRRIES are multistage centrifugal units which operate below water level and are driven by water filled AC single phase (or) three phase induction submersible motors. There pumps are will suited for borewell diameter of minimum 4″ (or) 100 mm . These pumps work on principle of a modular structure where with limited number of parts different tailor made request can be achieved.Impellers and diffusers are manufactured with high grade stainless steel which can be well suited for salty conditions and better performance.
| Power Range | 1.0 H.P – 7.5 H.P |
|---|---|
| Speed | 2900 RPM |
| Operating Voltage | Single phase ( 180 V to 230 V ) AC |
| Three phase ( 360 V to 415 V ) AC | |
| Delivery Pipe Size | 32 mm |
| Max. Outer Diameter | 98 mm |
| Head Range | 25 mtrs – 350 mtrs |
| Discharge | 3.5 LPS – 0.3 LPS |
| Maximum Start / Hour | 20 times |
| Method of starting | CSCR – 1 Phase |
| DOL – 3 Phase |
| Outer pipe | S.S. 202 |
|---|---|
| Shaft | S.S. 410 |
| Thrust bearing set | Impregnated Carbon / S.S |
| Bearing Bush | LTB 4 |
| Impeller / Diffuser | Stainless Steel |
| Diaphragm | Nitrile Butyl Rubber (NBR) |
4″ submersible pump of KMP INDUSTRRIES are multistage centrifugal units which operate below water level and are driven by water filled AC single phase (or) three phase induction submersible motors. There pumps are will suited for borewell diameter of minimum 4″ (or) 100 mm. A dynamically balanced rotor rotates in a oversized twin bearings on each bearing housing. An installed diaphragm in the lower motor housing provides pressure / volume compensation of the motor during internal motor temperature changes .
| Power Range | 0.75 H.P – 7.5 H.P |
|---|---|
| Speed | 2900 RPM |
| Head Range | 25 mtrs – 570 mtrs |
| Discharge | 6.0 LPS – 0.2 LPS |
| Operating Voltage | Single phase ( 180 V to 230 V ) AC |
| Three phase ( 360 V to 415 V ) AC | |
| Delivery Pipe Size | 25mm, 32 mm , 40 mm , 50 mm |
| Max. Outer Diameter | 98 mm |
| Method of starting | CSCR – 1 Phase |
| DOL – 3 Phase | |
| Maximum Start / Hour | 20 times |
| Outer pipe | S.S. 202 |
|---|---|
| Shaft | S.S. 410 |
| Impeller / Diffuser | Noryl |
| Thrust bearing set | Impregnated Carbon / S.S |
| Bearing Bush | LTB 4 |
| Diaphragm | Nitrile butyl Rubber (NBR) |
5″ Submersible pumpsets of KMP INDUSTRRIES are multistage centrifugal units which operate below water level and are driven by water filled AC ) three phase induction submersible motors. There pumps are will suited for borewell diameter of minimum 5″ (or) 125 mm . Good remedy for improperly drilled 6″ bore holes & Sandy borewells.Impellers and diffusers are manufactured with high grade stainless steel which can be well suited for salty conditions and better performance.
| Power Range | 3.0 H.P – 12.5 H.P |
|---|---|
| Speed | 2900 RPM |
| Operating Voltage | Three phase ( 360 V to 415 V ) AC |
| Delivery Pipe Size | 40 mm , 50 mm |
| Max. Outer Diameter | 125 mm |
| Head Range | 45 mtrs – 650 mtrs |
| Discharge | 8.0 LPS – 1.0 LPS |
| Maximum Start / Hour | 20 times |
| Method of starting | DOL – 3 Phase |
| Outer pipe | S.S. 202 |
|---|---|
| Shaft | S.S. 410 |
| Thrust bearing set | Impregnated Carbon / S.S |
| Bearing Bush | LTB 4 |
| Impeller / Diffuser | Cast Iron / Stainless Steel |
| Diaphragm | Nitrile Butyl Rubber (NBR) |
V5 to V4 submersible pump of KMP INDUSTRRIES are multistage centrifugal units which operate below water level and are driven by water filled AC three phase induction submersible motors. In this type V5 motor is connected with V4 Stainless steel pump.These pumps are will suited for borewell diameter of minimum 6″ (or) 150 mm.
| Power Range | 5.0 H.P – 12.5 H.P |
|---|---|
| Speed | 2880 RPM |
| Operating Voltage | Three phase ( 360 V to 415 V ) AC |
| Delivery Pipe Size | 32 mm, 40 mm |
| Max. Outer Diameter | 98 mm |
| Head Range | 15 mtrs – 620 mtrs |
| Discharge | 2.0 LPS – 0.3 LPS |
| Method of starting | DOL – 3 Phase |
| Outer pipe | S.S. 202 |
|---|---|
| Shaft | S.S. 410 |
| Thrust bearing set | Impregnated Carbon / S.S |
| Bearing Bush | LTB 4 |
| Impeller / Diffuser | Stainless Steel |
| Diaphragm | Nitrile Butyl Rubber (NBR) |
The 6″ Vertical borewell submersible pumps are well suited for 150 mm borewell and above. These submersible pumps consists of multistage centrifugal, vertical axis pumps. The pumps are designed such that series of impellers rotate inside vane diffusers challenging the flow of fluid from each impeller to the suction opening of the next. The fluid passes through the series of impellers and leaves the pump via delivery outlet.
The 6″ submersible pumpsets have a complete balance between hydraulic and electric design. The electrically driven motors are water cooled type, and the rotor is mounted in a carbon thrust bearing which absorbs axial thrust, where as mixed flow type pumps are for medium heads and high discharge. This is a compact unit which operates beneath the surface of water and is suspended vertically from raising main when installed.
The 6″ submersible pumpsets have a complete balance between hydraulic and electric design. The electrically driven motors are water cooled type, and the rotor is mounted in a carbon thrust bearing which absorbs axial thrust, where as mixed flow type pumps are for medium heads and high discharge. This is a compact unit which operates beneath the surface of water and is suspended vertically from raising main when installed.
| Power Range | 3.0 H.P – 15.0 H.P |
|---|---|
| Speed | 2900 RPM |
| Operating Voltage | 415 V / 50 Hz AC Supply |
| Delivery Pipe Size | 50 mm |
| Impeller Type | Mixed \ Bowl |
| Head Range | 30 mts – 120 mts |
| Discharge | 20.0 LPS – 2.0 LPS |
| Maximum Start / Hour | 15 times |
| Method of starting | STAR / STAR DELTA |
| Outer pipe | S.S. 202 / S.S 304 |
|---|---|
| Rotor Shaft | S.S. 410 / S.S 416 |
| Thrust bearing set | Impregnated Carbon / S.S |
| Vertical Bearing Bush | LTB 4 |
| Impeller | Stainless Steel |
| Diffusers | Cast iron |
| Suction / NRV | Cast Iron FG 200 / FG 250 |
The 6″ Vertical borewell submersible pumps are well suited for 150 mm borewell and above. These submersible pumps consists of multistage centrifugal, vertical axis pumps. The pumps are designed such that series of impellers rotate inside vane diffusers challenging the flow of fluid from each impeller to the suction opening of the next. The fluid passes through the series of impellers and leaves the pump via delivery outlet.
| Power Range | 3.0 H.P – 25.0 H.P |
|---|---|
| Speed | 2900 RPM |
| Operating Voltage | 415 V / 50 Hz AC Supply |
| Delivery Pipe Size | 50 mm |
| Head Range | 30 mts – 330 mts |
| Discharge | 9.0 LPS – 2.0 LPS |
| Maximum Start / Hour | 15 times |
| Method of starting | STAR / STAR DELTA |
| Outer pipe | S.S. 202 / S.S 304 |
|---|---|
| Rotor Shaft | S.S. 410 / S.S 416 |
| Thrust bearing set | Impregnated Carbon / S.S |
| Bearing Bush | LTB 4 |
| Impeller | Stainless Steel |
| Diffusers | Cast iron |
| Suction / NRV | Cast Iron FG 200 / FG 250 |
| Diaphragm | Nitrile Butyl Rubber (NBR) |
Single phase openwell submersible pumps are suitable for openwells and underground sumps. These pumps rests at the bottom of the well hence reducing the risk of water level fluctuating problem.These pumps are made of high grade stainless steel body and cast iron parts. The motor portion is a water cooled easily rewindable type, where the windings are made using special insulated copper wires a specially designed thrust bearings are used to withstand axial thrust load. It has a very simple pump portion comprising of a bowl and impeller with a unique hydraulic design to provide a high efficient performance
| Power Range | 0.5HP – 3.0 HP |
|---|---|
| Installation method | Horizontal |
| Power Supply | 1 Phase 230 V AC |
| 3 Phase 415 V AC | |
| Pump Outlet Size | 25 mm, 32 mm, 40 mm, 50 mm |
| Impellers | S.S 202 |
| Head Range | 10 mtrs – 35 mtrs |
| Discharge | 8.5 LPS – 3.0 LPS |
| Maximum Start / Hour | 6 times |
| Type of Duty | Continues |
Three phase vertical openwell submersible pumps are multistage type which helps to increase the head range. The motor is bound with special water proof insulated winding wires and hence it is capable of withstanding wide voltage fluctuations. Specially designed thrust bearing are used to withstand axial thrust loads with minimum wear.
| Power Range | 3.0 H.P – 100.0 H.P |
|---|---|
| Speed | 2880 RPM |
| Power Supply | 380 – 415 V , 3 Phase , 50 Hz AC Supply |
| Head Range | 15 mtrs – 325 mtrs |
| Discharge | 4.0 LPS – 60.0 LPS |
| Type of Duty | S1 ( Continues ) |
KMP Three phase Horizontal openwell submersible pump in cast iron construction has wide applications in agriculture and domestic segment. Due to numerous advantages over centrifugal pumps these are good replacement for the application. These pumps are ideally suitable for openwells or tanks where there is a wide fluctuation in water level. This pumps works under water and it rests at bottom of well hence suction and priming problem do not arise
| Power Range | 3.0 H.P – 20.0 H.P |
|---|---|
| Speed | 2880 RPM |
| Power Supply | 380 – 415 V , 3 Phase , 50 Hz AC Supply |
| Delivery Pipe Size | 25 mm |
| Head Range | 8 mtrs – 50 mtrs |
| Discharge | 3.0 LPS – 40.0 LPS |
| Type of Duty | S1 ( Continues ) |
We KMP Industrries manufacture CELVIN brand self Priming Monoblock Pumps with a high engineering excellence to meet common as well as most technology needs of the society. CELVIN Pumps are made up of high selective quality materials under strict quality control Supervision.
Performance at 2880 RPM, 200 – 240V, 50Hz AC Supply
| Power Range | 0.5 H.P – 1.0 H.P |
|---|---|
| Speed | 2880 RPM |
| Power Supply | 1 Phase 230 V AC |
| Delivery Pipe Size | 25 mm |
| Head Range | 8 mtrs – 50 mtrs |
| Discharge | 0.2 LPS – 1.5 LPS |
| Type of Duty | S1 ( Continues ) |
We KMP Industrries manufacture CELVIN brand centrifugal Monoblock Pumps with a high engineering excellence to meet common as well as most technology needs of the society. CELVIN Pumps are made up of high selective quality materials under strict quality control Supervision.
| Power Range | 0.5 H.P – 3.0 H.P |
|---|---|
| Speed | 2880 RPM |
| Power Supply | 1 Phase 230 V AC |
| Delivery Pipe Size | 25 mm , 32 mm ,40 mm ,50 mm, 65 mm, 75 mm |
| Head Range | 8 mtrs – 25 mtrs |
| Discharge | 0.2 LPS – 12 LPS |
| Type of Duty | S1 ( Continues ) |
KMP UPVC Pipes is one among such accessories produced with specially designed formulation under integrated quality control system .The compound has hydrostatic design stress of 2000 psi for water at 73.4 degree Fahrenheit tested accordance with ASTMD 2837.
Made using the best quality material, these power cables consist of highly abrasion resistant PVC sheath impervious to grease, oil, water, etc. Ensure protection against electrical hazards, like short- circuit, current leakage, etc, with these safe, reliable and durable flat submersible cables by Standard
5″ Submersible pumps of KMP INDUSTRRIES are multistage centrifugal units which operate below water level and are driven by water filled AC ) three phase induction submersible motors. There pumps are will suited for borewell diameter of minimum 5″ (or) 125 mm . Good remedy for improperly drilled 6″ bore holes & Sandy borewells. Impellers and diffusers are manufactured with high grade stainless steel which can be well suited for salty conditions and better performance.
| Power Range | 3.0 H.P – 12.5 H.P |
|---|---|
| Speed | 2900 RPM |
| Operating Voltage | Three phase ( 360 V to 415 V ) AC |
| Delivery Pipe Size | 40 mm , 50 mm |
| Max. Outer Diameter | 125 mm |
| Head Range | 45 mtrs – 650 mtrs |
| Discharge | 8.0 LPS – 1.0 LPS |
| Maximum Start / Hour | 20 times |
| Method of starting | DOL – 3 Phase |
| Outer pipe | S.S. 202 |
|---|---|
| Shaft | S.S. 410 |
| Thrust bearing set | Impregnated Carbon / S.S |
| Bearing Bush | LTB 4 |
| Impeller / Diffuser | Cast Iron / Stainless Steel |
| Diaphragm | Nitrile Butyl Rubber (NBR) |